 | C.R. LAURENCE CN0035 CRL Top Pulley Shaft and Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0035
C.R. LAURENCE CN0035 CRL Top Pulley Shaft and Bearing for the GL4W or CN4106 Sander. This CRL Top Pulley Shaft and Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools. | *$111.50 |
 | C.R. LAURENCE CN0036 CRL Roller Platen for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0036
C.R. LAURENCE CN0036 CRL Roller Platen for the GL4W or CN4106 Sander. This CRL Roller Platen is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools.. | *$476.14 |
 | C.R. LAURENCE CN0037 CRL Roller Platen Shaft Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0037
C.R. LAURENCE CN0037 CRL Roller Platen Shaft Bearing for the GL4W or CN4106 Sander. This CRL Roller Platen Shaft Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools.. | *$108.76 |
 | C.R. LAURENCE CN0038 CRL Bottom Bracket and Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0038
C.R. LAURENCE CN0038 CRL Bottom Bracket and Bearing for the GL4W or CN4106 Sander. This CRL Bottom Bracket and Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools.. | *$164.37 |
 | C.R. LAURENCE CN0039 CRL Lower Pulley for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0039
C.R. LAURENCE CN0039 CRL Lower Pulley for the GL4W or CN4106 Sander. This CRL Lower Pulley is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools.. | *$199.41 |
 | C.R. LAURENCE CN0040 CRL Bottom Bracket Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0040
C.R. LAURENCE CN0040 CRL Bottom Bracket Bearing for the GL4W or CN4106 Sander. This CRL Bottom Bracket Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools.. | *$122.37 |
 | C.R. LAURENCE CPT10X12 CRL 10" x 12" Glass Cutting Table Carpet
Brand: C.R. Laurence Part Number: CPT10X12
C.R. LAURENCE CPT10X12 CRL 10" x 12" Glass Cutting Table Carpet. This CRL Glass Cutting Table Carpet is precut to fit your table. There is sufficient extra material to allow the carpet to be wrapped around the table"s edge and secured. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$455.33 |
| C.R. LAURENCE CPT6X8 CRL 6" x 8" Glass Cutting Table Carpet
Brand: C.R. Laurence Part Number: CPT6X8
C.R. LAURENCE CPT6X8 CRL 6" x 8" Glass Cutting Table Carpet. This CRL Glass Cutting Table Carpet is precut to fit your table. There is sufficient extra material to allow the carpet to be wrapped around the table"s edge and secured. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$330.30 |
| C.R. LAURENCE CPT8X10 CRL 8" x 10" Glass Cutting Table Carpet
Brand: C.R. Laurence Part Number: CPT8X10
C.R. LAURENCE CPT8X10 CRL 8" x 10" Glass Cutting Table Carpet. This CRL Glass Cutting Table Carpet is precut to fit your table. There is sufficient extra material to allow the carpet to be wrapped around the table"s edge and secured. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$482.56 |
| C.R. LAURENCE CPT8X12 CRL 8" x 12" Glass Cutting Table Carpet
Brand: C.R. Laurence Part Number: CPT8X12
C.R. LAURENCE CPT8X12 CRL 8" x 12" Glass Cutting Table Carpet. This CRL Glass Cutting Table Carpet is precut to fit your table. There is sufficient extra material to allow the carpet to be wrapped around the table"s edge and secured. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$455.33 |
| C.R. LAURENCE CPT9X12 CRL 9" x 12" Glass Cutting Table Carpet
Brand: C.R. Laurence Part Number: CPT9X12
C.R. LAURENCE CPT9X12 CRL 9" x 12" Glass Cutting Table Carpet. This CRL Glass Cutting Table Carpet is precut to fit your table. There is sufficient extra material to allow the carpet to be wrapped around the table"s edge and secured. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$455.33 |
| C.R. LAURENCE CPTL1N CRL 12 Foot Wide Glass Cutting Table Carpet Cut to Length
Brand: C.R. Laurence Part Number: CPTL1N
C.R. LAURENCE CPTL1N CRL 12 Foot Wide Glass Cutting Table Carpet Cut to Length. This CRL 12 Foot Wide Glass Cutting Table Carpet is cut to the length you need from bulk rolls. Viewing score lines and detecting glass chips to avoid scratching lites of glass is easy because of it"s black color. This is not indoor/outdoor carpet, it is specifically made for high use wear and the high density gives you the perfect cushioning effect needed for scoring and break out.. | *$43.90 |
 | C.R. LAURENCE DMC55GL CRL 55 Gallon Diamond Machine Coolant
Brand: C.R. Laurence Part Number: DMC55GL
C.R. LAURENCE DMC55GL CRL 55 Gallon Diamond Machine Coolant. CRL Diamond Machine Coolant is a high-performance, cost effective lubricant that is highly concentrated. The concentration on this product is usually between 50:1 to 100:1. With addition at tank side or by automated metering equipment, this product accommodates grinding bevels of up to two inches (50.8 millimeters). CRL DMC55 is considered a heavy duty lubricant that can even extend the life of the sump. It is designed with long-lasting microbiological protection suited for heavy use situations experienced in even the largest of glass facilities. It also reduces the development of "popcorn" particles during grinding to keep the lines clear. CRL DMC55 is manufactured with the environment in mind, using a water-based formulation containing absolutely no oil. It is also pH-controlled at moderate levels to facilitate operator handling.. | *$1,095.61 |
 | C.R. LAURENCE DMC5GL CRL 5 Gallon Diamond Machine Coolant
Brand: C.R. Laurence Part Number: DMC5GL
C.R. LAURENCE DMC5GL CRL 5 Gallon Diamond Machine Coolant. CRL Diamond Machine Coolant is a high-performance, cost effective lubricant that is highly concentrated. The concentration on this product is usually between 50:1 to 100:1. With addition at tank side or by automated metering equipment, this product accommodates grinding bevels of up to two inches (50.8 millimeters). CRL DMC55 is considered a heavy duty lubricant that can even extend the life of the sump. It is designed with long-lasting microbiological protection suited for heavy use situations experienced in even the largest of glass facilities. It also reduces the development of "popcorn" particles during grinding to keep the lines clear. CRL DMC55 is manufactured with the environment in mind, using a water-based formulation containing absolutely no oil. It is also pH-controlled at moderate levels to facilitate operator handling.. | *$147.49 |
 | C.R. LAURENCE DTB101 CRL 62" Replacement Diamond Coated Band Saw Blade for the DTB5000
Brand: C.R. Laurence Part Number: DTB101
C.R. LAURENCE DTB101 CRL 62" Replacement Diamond Coated Band Saw Blade for the DTB5000. This CRL Diamond Coated Replacement Blade is designed for use on the CRL DTB5000 Diamond Laser Band Saw.. | *$256.60 |
 | C.R. LAURENCE DTB3000 CRL Diamond Band Saw
Brand: C.R. Laurence Part Number: DTB3000
C.R. LAURENCE DTB3000 CRL Diamond Band Saw. The CRL Diamond Band Saw can clean-cut virtually any glass shape, including curves with a radius as small as 1/4 inch (6.4 millimeter). The 36 inch (914.4 millimeter) precision blade is bathed continuously in coolant to prolong life and prevent dust, all the while producing a clean-cut edge that requires little or no finishing. Also cuts tile, ceramics and other brittle craft items. You can stack identical shapes and cut multiple pieces simultaneously. Quiet 110V AC motor has a variable speed (0-2,800 rpm) control, and saw housing is made of rugged aluminum and stainless steel.. | *$900.75 |
 | C.R. LAURENCE EAF CRL Counter Balance Table Air Flotation System
Brand: C.R. Laurence Part Number: EAF
Easy to Install on any Glass Cutting Table Positions Glass on a Cushion of Air Safely and Easily 110 Volt Electrical Requirement Improve your cutting table by installing air flotation. The CRL Counter Balance Table Air Flotation System is easy to install, and allows you to float, move and easily turn glass on the table top. Contains a self-contained blower system, hose, and 12 check ball outlets. Number of Outlets: 12 Electrical Requirement: 110 Volts F.O.B : Red Oak, TX | *$1,771.00 |
 | C.R. LAURENCE ERB2 CRL Ball Caster for IG Tables
Brand: C.R. Laurence Part Number: ERB2
C.R. LAURENCE ERB2 CRL Ball Caster for IG Tables. This spherical CRL Ball Caster is two inches (51 millimeters) in diameter, made of neoprene, and is used on ball caster-type Transfer, Inspection and Tilt tables. The balls will not scratch the glass as it glides over them.. | *$13.64 |
 | C.R. LAURENCE ERR1 CRL Stab-In Glass Cutting Table Rollers
Brand: C.R. Laurence Part Number: ERR1
Makes Glass Loading Easy When Table is in Upright Position Easy to Install and Remove CRL ERR1 Stab-In Glass Cutting Table Rollers make an efficient add-on to any tilt-top glass cutting table. The set of four durable rubber rollers mount into steel collars that are recessed into the table's surface. Positioned so they align with your vertical glass storage racks when your table is in the upright position, glass can be easily loaded onto the rollers safely. When the table is then lowered to the horizontal position, the rollers are simply pulled out of the steel collars so you're ready to cut glass. Four each per set. F.O.B : Red Oak, TX | *$1,372.55 |
 | C.R. LAURENCE EW CRL Electric Winch for Glass Cutting Tables
Brand: C.R. Laurence Part Number: EW
Pulls Glass from Vertical Storage Racks onto Tilt-Top Glass Cutting Tables. Provides Safe, Effortless Loading 110 Volt Electrical Power Source The CRL Electric Winch for Glass Cutting Tables takes the strain out of pulling large lites of glass from verical storage racks onto tilt-top cutting tables when they are in the tilt up position. By attaching a CRL Woods Powr-Grip pump type vacuum cup to the winch's cable, the glass is drawn onto the table's wooden or roller toes that have been matched in height to the storage rack floor. The cable is made of strong polyester material so there is no chance of scratching the glass during loading. The CRL Electric Winch for Glass Cutting Tables is powered by your 110 volt electrical system. Voltage Requirement: 110 Volts F.O.B : Red Oak, TX. | *$1,914.77 |
 | C.R. LAURENCE H82 CRL 4" x 106" Horizontal Wet Belt Sander
Brand: C.R. Laurence Part Number: H82
C.R. LAURENCE H82 CRL 4" x 106" Horizontal Wet Belt Sander. This CRL Horizontal Wet Belt Sander is good for grinding vase bottoms or pottery. It uses standard 4 x 106 inch (102 x 1,626 millimeter) wet/dry glass grinding belts that are directly driven by a One H.P. 110-220 volt single phase motor. The steel pulleys and belt tightening device are the same as those used on CRL Upright Glass Sanding Machines. The water spray nozzle keeps the belt wet to reduce heat from friction and grinding dust. There is a flat platen behind the belt at the drive end of the tank.. | *$4,188.47 |
 | C.R. LAURENCE T10 CRL 10" Diamond Glass Saw
Brand: C.R. Laurence Part Number: T10
C.R. LAURENCE T10 CRL 10" Diamond Glass Saw. This CRL 10 Inch Diamond Saw makes straight and square cuts accurately and quickly. Works best on 1/4 inch (6.4 millimeter) thick glass, and will cut glass up to four inches (102 millimeters) in height. Great for cutting super-hard or bulletproof glass. There is a solid plastic table top cutting surface and unbreakable plastic drip tank which cleans out easily. Maximum strip cut is 2-3/4 inches (70 millimeters) wide using the included guide. Maximum freehand cut is 5-3/4 inches (146 millimeters).. | *$918.92 |
 | C.R. LAURENCE T6 CRL 6" Diamond Glass Saw
Brand: C.R. Laurence Part Number: T6
C.R. LAURENCE T6 CRL 6" Diamond Glass Saw. Make straight and square cuts accurately and quickly with this CRL Diamond Saw. The saw works best on glass 1/4 inch (6.4 millimeter) thick, but can cut glass up to 1-1/2 inches (38 millimeters) thick. It is great for cutting super-hard cathedral glass or bullet-proof glass laminate strips up to five inches (127 millimeters) wide. The Blade has a diamond impregnated edge for neat, smooth cuts. There is also a solid plastic table top cutting surface measuring 15 by nine inches (381 by 229 millimeters) and unbreakable plastic drip tank which cleans out easily.. | *$747.91 |
 | C.R. LAURENCE VTP1T CRL Panther Instructional Video Tape
Brand: C.R. Laurence Part Number: VTP1T
C.R. LAURENCE VTP1T CRL Panther Instructional Video Tape. This videotape depicts the basic unpacking, assembly and operation of the CRL Panther Automatic Diamond Glass Edger. Also shows basic maintenance and the machines limits. It is included when purchasing the CRL Panther Edger. Total of length of video is 46 minutes.. | *$29.63 |
 | Campbell S30-80campbell S30-80 Point Wel 1-1/4x30" 80gz
Brand: Campbell Model: S30-80 Part Number: S30-80
WELL POINT
Self-flushing chamfered half- moon slots eliminate clay build-up
Internal stainless steel screen
No welded seams on screen
Can be used as a drive point, suction strainer, or for jet pump installation
NSF approved PVC pipe lining
Bagged
80 Gauze; 1-1/4x30 | *$61.99 |
| | Chain Hoist with 12' of Chain
Brand: CM Part Number: 5605 | *$195.00 |
| | Big Orange Hitch Pins With Hairpin Lock - HITCH PIN 1" x 6-3/4"L.
Brand: CM Chain Part Number: 1230
Big Orange Hitch Pins With Hairpin Lock - Hot forged of high-strength steel; hardened and tempered for maximum strength; will not break or bend. Complete with hairpin lock. Painted orange. Carton pac | *$20.85 |
 | Big Orange Hitch Pins With Hairpin Lock - HITCH PIN 3/4" x 6-1/4"L.
Brand: CM Chain Part Number: 1220
Big Orange Hitch Pins With Hairpin Lock - Hot forged of high-strength steel; hardened and tempered for maximum strength; will not break or bend. Complete with hairpin lock. Painted orange. Carton pac | *$17.41 |
| | Big Orange Hitch Pins With Hairpin Lock - HITCH PIN 7/8" x 6-1/2"L.
Brand: CM Chain Part Number: 1225
Big Orange Hitch Pins With Hairpin Lock - Hot forged of high-strength steel; hardened and tempered for maximum strength; will not break or bend. Complete with hairpin lock. Painted orange. Carton pac | *$27.84 |
 | Wire Stretcher No. 44, 250 Lb
Brand: CM CPG Part Number: 12368
Wire Stretcher No. 44. For light duty hoisting. | *$46.99 |
 | Columbus McKinnon 12376 Wire Grip
Brand: Columbus McKinnon Part Number: 12376
Malleable iron. Yellow chromated. Standard #25. | *$8.29 |
 | Columbus McKinnon M1196E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1196E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$5.99 |
| Columbus McKinnon M1201E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1201E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$5.80 |
 | Columbus McKinnon M1205 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Part Number: M1205
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$6.08 |
| Columbus McKinnon M1206E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1206E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$6.49 |
 | Columbus McKinnon M1220 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Model: M1220 Part Number: M1220
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$5.99 |
| Columbus McKinnon M1221E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1221E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$6.66 |
| Columbus McKinnon M1225 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Part Number: M1225
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$9.11 |
| Columbus McKinnon M1226E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1226E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$8.00 |
 | Columbus McKinnon M1230 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Model: M1230 Part Number: M1230
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$7.42 |
| Columbus McKinnon M1231E E-Grip Hitch Pin
Brand: Columbus McKinnon Part Number: M1231E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$10.15 |
 | Fence Stretcher Splicer - 12372 Wire Fence Stretcher
Brand: Columbus McKinnon Part Number: 12372
FENCE STRETCHER SPLICER - Stops rivet both sides ~ Keeps ratchet on bar ~ Weighs 8-7/8 lbs. ~ 1 000 lb. work load limit | *$66.73 |
| Hitch Pins
Brand: Columbus McKinnon Part Number: M1205
Hot forged pin. Micro allow steel. Folding wire handle. Easy-to-grip, easy-to-attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1/2" pin diameter; 3-1/2" useable length, wire handle No. M1200: 5/8" pin diameter, 3-3/4" useable length, wire handle No. M1205: 3/4" pin diameter, 4" useable length, wire handle No. M1211: 7/8" pin diameter, 4-1/4" useable length, solid handle No. M1220: 3/4" pin diameter, 6-1/4" useable length, wire handle No. M1225: 7/8" pin diameter, 6-1/2" useable length, wire handle No. M1230: 1" pin diameter, 6-3/4" useable length, wire handle | *$3.69 |
| Hitch Pins
Brand: Columbus McKinnon Part Number: M1225
Heat treated for strength properties|Complete with grip clip | *$5.62 |
 | Swivel Wire Grip - 12373 Swivel Wire Grip
Brand: Columbus McKinnon Part Number: 12373
SWIVEL WIRE GRIP - Malleable iron grip for wire stretcher ~ Cast ductile jaws for long life ~ Approximate weight: 4 lbs. | *$18.15 |
 | COOPER GROUP/CAMPBELL #T3899720 5/8x3-3/4 Hitch Pin
Brand: Cooper Part Number: T3899720
5/8" x 3-3/4" Hitch Pin, Drop Forged Galvanized, With Clips, Use Clip Item #485-599, Tagged. | *$6.37 |
 | COOPER GROUP/CAMPBELL #T3899768 7/8x6-1/2 Hitch Pin
Brand: Cooper Part Number: T3899768
7/8" x 6-1/2" Hitch Pin, Drop Forged Galvanized, With Clips, Use Clip Item #485-607, 2 Per Box. | *$11.83 |
 | 10 7/16" Heavy Duty Fencesld Joint Pliers Carded (181-193610VN) Category: Fencing Pliers
Brand: Cooper Hand Tools Part Number: 193610VN
Item #: 181-193610VN. 2 staple grips in nosebrCorrugated hammer head with heavy prong to easily reach and pull rusty staplesbrSpecial openings in head allows both wire and staple to be grippedbr2 Electronically induction hardened durable wire cuttersbrPolished head pulliPacking Type = CardedliOverall Length = 10 7/16 inliJaw Length = 1 1/16 inliJaw Width = 3 5/8 inliJaw Thickness = 19/32 inliJaw Shape = CurvedliHandle Type = Cushion GripliMaterial = Forged Alloy SteelliType = Fence PliersliWt. = 24.96 oz/ul brCustomers also search for: Discount 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, Buy 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, Wholesale 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, 037103212955, 193610VN, Fencing Pliers | *$23.21 |
 | Blkwidow Insltor Wdpt 25/Pkg
Brand: DARE Part Number: BW-WP-25(500
High density black linear polyethylene for sunlight resistance. Operates well in any climate, in any part of the world. 45 degree slot easily accepts any fence wire and holds it is place. Black only 25 to a package 20 packages to a case. | *$3.46 |
 | Dare Prod. 2880 Tape Buckle And Gate Anchor
Brand: DARE Model: 2880 Part Number: 2880
For tape up to 1 2" polytape. Use to splice 2 lengths of tape. Attach to pinlock insulator to form gate anchor or tape end. Has many uses. 2 buckles per package. | *$4.10 |
