 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, 5/8in. Shaft, Model# GP-F20-04-P-A
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.24 cu. in./rev. Max. PSI: 3,650, Shaft Diameter (in.): 5/8, Material: Aluminum, Rotations Per Minute: 3,600, Weight (lbs.): 5.20 | *$175.99 |
 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, Spline 9-Tooth Shaft, Model# GP-F20-14-S9-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.85 cu. in./rev. Max. PSI: 3,650, Shaft Type: Spline 9-tooth, Material: Aluminum, Rotations Per Minute: 3,600, Weight (lbs.): 6.00 | *$185.99 |
 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, 3/4in. Shaft, Model# GP-F20-04-P1-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.24 cu. in./rev. Max. PSI: 3,650, Shaft Diameter (in.): 3/4, Material: Aluminum, Rotations Per Minute: 3,600, Weight (lbs.): 5.20 | *$185.99 |
 | Elkhart Products 10155516 Push on Slip Coupling 3/4"
Brand: Elkhart Model: 10155516 Part Number: 10155516
"ELKHART PRODUCTS" PUSH ON SLIP COUPLING
Size: 3/4"
Push on slip coupling.
Includes insert for pex piping.
For tectite fittings, heat free method for joining copper.
A removable reusable fitting system that provides the ultimate flexibility.
Contains less than .025 percent weighted average lead content on wetted surfaces, california vermont low lead compliant. | *$13.24 |
 | Elkhart Prod. Corp. 10170000 QTite Coupling With Stop
Brand: Elkhart Model: 10170000 Part Number: 10170000
Coupling with stop. QTite fittings provide a clean and easy joining method that's designed to save time and money on installations. Installing a joint with QTite is simple, requiring no extra materials beyond the QTite fitting for copper and CPVC tubing installations, a QTite fitting plus a tube liner for PEX (included) installations. No more solder, flux, or special pressing tools needed. The result lowers costs, reduced labor time, and a clean and efficiant process. No. 10170000: 1 2'' No. 10170005: 3 4'' No. 10170010: 1'' | *$2.86 |
 | Elkhart Prod. Corp. 10170005 QTite Coupling With Stop
Brand: Elkhart Model: 10170005 Part Number: 10170005
Coupling with stop. QTite fittings provide a clean and easy joining method that's designed to save time and money on installations. Installing a joint with QTite is simple, requiring no extra materials beyond the QTite fitting for copper and CPVC tubing installations, a QTite fitting plus a tube liner for PEX (included) installations. No more solder, flux, or special pressing tools needed. The result lowers costs, reduced labor time, and a clean and efficiant process. No. 10170000: 1 2'' No. 10170005: 3 4'' No. 10170010: 1'' | *$3.27 |
 | Elkhart Prod. Corp. 10170120 QTite Male Adapter
Brand: Elkhart Part Number: 10170120
QTite, Male adapter, fittings provide a clean and easy joining method that's designed to save time and money on installations. Installing a joint is simple, requires no extra materials for copper and CPVC tubing installations, and a tube liner for PEX installations, no more solder, flux, heat, or special pressing tools needed. Results in lower costs, reduced labor time, and a clean and efficient installation process. No. 10170120: 1 2'' No. 10170125: 3 4'' | *$3.03 |
 | Elkhart Prod. Corp. 10170030 QTite Reducing Coupling Less Stop
Brand: Elkhart Part Number: 10170030
QTite, 3 4'' x 1 2'' reducing coupling, less stop. QTite fittings provide a clean and easy joining method that's designed to save time and money on installations, installing a joint is simple, requires no extra materials for copper and CPVC tubing installations , and a tube liner for PEX installations, no more solder, flux, heat, or special pressing tools needed. Results in lower costs, reduced labor time, and a clean and efficient installation process. | *$4.96 |
 | Elkhart Prod. Corp. 10170095 QTite Female Adapter
Brand: Elkhart Part Number: 10170095
QTite, Female adapter fittings provide a clean and easy joining method that's designed to save time and money on installations, installing a joint is simple, requires no extra materials for copper and CPVC tubing installations and a tube liner for PEX installations, no more solder, flux, heat, or special pressing tools needed. Results in lower costs, reduced labor time, and clean and efficient installation process. No. 10170090: 1 2'' No. 10170095: 3 4'' | *$4.14 |
 | Elkhart Prod. Corp. 10170010 QTite Coupling With Stop
Brand: Elkhart Part Number: 10170010
Coupling with stop. QTite fittings provide a clean and easy joining method that's designed to save time and money on installations. Installing a joint with QTite is simple, requiring no extra materials beyond the QTite fitting for copper and CPVC tubing installations, a QTite fitting plus a tube liner for PEX (included) installations. No more solder, flux, or special pressing tools needed. The result lowers costs, reduced labor time, and a clean and efficiant process. No. 10170000: 1 2'' No. 10170005: 3 4'' No. 10170010: 1'' | *$7.82 |
| Elkhart Prod. Corp. 10170090 QTite Female Adapter
Brand: Elkhart Part Number: 10170090
QTite, Female adapter fittings provide a clean and easy joining method that's designed to save time and money on installations, installing a joint is simple, requires no extra materials for copper and CPVC tubing installations and a tube liner for PEX installations, no more solder, flux, heat, or special pressing tools needed. Results in lower costs, reduced labor time, and clean and efficient installation process. No. 10170090: 1 2'' No. 10170095: 3 4'' | *$3.29 |
| Elkhart Prod. Corp. 10170125 QTite Male Adapter
Brand: Elkhart Part Number: 10170125
QTite, Male adapter, fittings provide a clean and easy joining method that's designed to save time and money on installations. Installing a joint is simple, requires no extra materials for copper and CPVC tubing installations, and a tube liner for PEX installations, no more solder, flux, heat, or special pressing tools needed. Results in lower costs, reduced labor time, and a clean and efficient installation process. No. 10170120: 1 2'' No. 10170125: 3 4'' | *$4.14 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder Short Arm No. CAS-51, Use w/cap.=1,250 lbs. (1 Each)
Brand: Enerpac Part Number: CAS-51
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$44.00 |
 | Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-9381ST (1 Each)
Brand: Enerpac Part Number: CST-9381
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$125.00 |
 | Enerpac Hydraulic Power Workholding No. STRD121, Light Duty, Double Acting, Threaded, w/o Arm (1 Each)
Brand: Enerpac Part Number: STRD-121
Hydraulic Power Workholding - Light Duty - These swing cylinders rotate 90° as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing or pull applications by loosening the bottom plug. All single acting cylinders come with a retract spring for single-acting operations. Max. psi 5,000. Clamp arms not included but sold separately below. Body styles available are threaded with upper flange or non-threaded with lower or upper flange. | *$398.00 |
 | Enerpac Hydraulic Power Workholding No. SURS51, Light Duty, Single Acting, Upper Flange, w/o Arm (1 Each)
Brand: Enerpac Part Number: SURS-51
These swing cylinders rotate 90 degrees as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing or pull applications by loosening the bottom plug. All single acting cylinders come with a retract spring for single-acting operations. Max. psi 5,000. Clamp arms not included but sold separately below. Body styles available are threaded with upper flange or non-threaded with lower or upper flange. | *$430.00 |
 | 81338 20t Hydraulic Pull (277-BHP-2751G) Category: Hydraulic Pullers
Brand: Enerpac Part Number: 277-BHP-2751G
Item #: 277-BHP-2751G. High quality, forged steel components provide superior reliability and servicebrSets included speed crank and adjusting screw for fast contact work before hydraulics are applied pulliCapacity Wt. = 20 tons [Max]liIncludes = P-392 Hand Pump, RCH-202 Cylinder, HP-2015 Saddle, HC-7206 Hose, GF-813P Gauge, GA-3 Gauge Adaptor, BHP-252 Grip Puller, BHP-262 Cross Bearing Puller, BHP-280 Bearing Cup Puller, BHP-282 Bearing Puller, CW-166 Wooden Case/ul brCustomers also search for: Discount 81338 20t Hydraulic Pull, Buy 81338 20t Hydraulic Pull, Wholesale 81338 20t Hydraulic Pull, 662005813384, BHP-2751G, Hydraulic Pullers | *$3,471.85 |
 | Hydraulic-Equipment - 5 Ton Cylinder, S/A
Brand: Enerpac Part Number: RC-51
Hydraulic-Equipment - 5 Ton Cylinder, S/A | *$216.95 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-18131ST (1 Each)
Brand: Enerpac Part Number: CTS18131
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$125.00 |
 | SEPTLS277RSM1500 - RSM Series Flat Jac Cylinders
Brand: Enerpac Part Number: 277-RSM-1500
RSM Series Flat Jac Cylinders | *$1,943.68 |
 | Enerpac Hydraulic Power Workholding Clamping Cylinder, Single Action, No. RW-102 (1 Each)
Brand: Enerpac Part Number: RW-102
Used for a wide range of production tooling applications, heavy duty force requirements and high cycle applications. Block shaped clamps provide a high amount of force in a tight area. Designed to be surface mounted on the machine tool bed or on a fixture surface. Provide force in horizontal or vertical direction. Cylindrical clamps have collar threads and base holes for mounting. All have spring return operation for easy unloading of workpiece and faster cycling. Spring is designed to return plunger only. | *$274.00 |
 | Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-271ST (1 Each)
Brand: Enerpac Part Number: TS-271ST
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$75.00 |
 | Enerpac Hydraulic Power Workholding Clamping Cylinder, Single Action, No. RW-53 (1 Each)
Brand: Enerpac Part Number: RW-53
Used for a wide range of production tooling applications, heavy duty force requirements and high cycle applications. Block shaped clamps provide a high amount of force in a tight area. Designed to be surface mounted on the machine tool bed or on a fixture surface. Provide force in horizontal or vertical direction. Cylindrical clamps have collar threads and base holes for mounting. All have spring return operation for easy unloading of workpiece and faster cycling. Spring is designed to return plunger only. | *$236.00 |
 | 20123 3/8" Speed D-coupl (277-A-604) Category: Hydraulic Tool Parts and Accessories
Brand: Enerpac Part Number: 277-A-604
Item #: 277-A-604. For medium duty applications, use with hand pumpsbrIncludes female steel dust cap pulliOperating Pressure = 10000.0 psi [Max]liFlow = 2500.0 cu. in./min [Max]liThread Size = 3/8 in (NPTF)liLength = 3.090 inliInside Style = Regular Spee-DliType = Complete Coupler SetliWt. = 1/2 lb/ul brCustomers also search for: Discount 20123 3/8" Speed D-coupl, Buy 20123 3/8" Speed D-coupl, Wholesale 20123 3/8" Speed D-coupl, 662005201235, A-604, Hydraulic Tool Parts and Accessories | *$37.85 |
 | Enerpac Hydraulic Power Workholding Hollow Cylinder, No. CY2129-25 (1 Each)
Brand: Enerpac Part Number: CY2129-25
These hollow cylinders combine compactness with power and versatility. Any application requiring either a pushing or pulling action is easily handled with this type of cylinder. The cylinders are threaded and can be placed over a bolt or a stud to upgrade most existing manual clamping fixtures. | *$301.00 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder Long Arm No. CAL-202, Use w/cap.=3,900 lbs. (1 Each)
Brand: Enerpac Part Number: CAL-202
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$97.00 |
 | Enerpac Hydraulic Power Workholding Low Profile Swing Clamp No. ASC-30, Clamp force=1,375 lbs. (1 Each)
Brand: Enerpac Part Number: ASC-30
These low profile swing clamps are designed to swing 97degrees to position the arm over the work piece. A vertical plunger then exerts an upward thrust on the back end of the swing arm providing powerful downward pressure to clamp the work piece. Arm can swing right or left. Operating pressure is 1,200 to 2,500 psi. | *$602.00 |
 | Enerpac Hydraulic Power Workholding Clamping Cylinder, Single Action, No. RW-50 (1 Each)
Brand: Enerpac Part Number: RW-50
Used for a wide range of production tooling applications, heavy duty force requirements and high cycle applications. Block shaped clamps provide a high amount of force in a tight area. Designed to be surface mounted on the machine tool bed or on a fixture surface. Provide force in horizontal or vertical direction. Cylindrical clamps have collar threads and base holes for mounting. All have spring return operation for easy unloading of workpiece and faster cycling. Spring is designed to return plunger only. | *$174.95 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder w/Arm No. SC-3, M=1-12 (1 Each)
Brand: Enerpac Part Number: SC-3
These swing cylinders rotate 90 degrees as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing, or pull applications by loosening the side plug and then rotating the plunger to a desired position. The VE-354 and VE-352 have a retract spring for single-acting operations. The VE-360 is only for double-acting operation and has no return spring. Clamp arm provided. Can be mounted with the built-in flange by securing the swinger to the top or bottom of a tooling plate or by screwing the threaded body into a mounting bracket. | *$425.00 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder Short Arm No. CAS-121, Use w/cap.=2,600 lbs. (1 Each)
Brand: Enerpac Part Number: CAS-121
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$53.00 |
 | Enerpac Hydraulic Power Workholding Work Support, Spring Advanced, No. WSL-111 (1 Each)
Brand: Enerpac Part Number: WSL-111
Work supports provide additional support to avoid excessive movement or deflection of the workpiece during machining. When hydraulic pressure is applied to the work support, a piston pushes against an internal adjustable spring that advances the work support plunger against a workpiece at the force set by the adjustable spring. As more hydraulic pressure is applied, an internal sleeve will grip and lock the plunger in that position. Available as a spring or fluid advance unit. The spring advanced unit can be converted to air by simply removing the internal adjustment spring and attaching a low pressure air line to the air breather vent tube. Operating pressure is 700 psi minimum, 5,000 psi maximum. | *$207.00 |
| Enerpac Hydraulic Power Workholding No. STRS121, Light Duty, Single Acting, Threaded, w/o Arm (1 Each)
Brand: Enerpac Part Number: STRS-121
These swing cylinders rotate 90 degrees as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing or pull applications by loosening the bottom plug. All single acting cylinders come with a retract spring for single-acting operations. Max. psi 5,000. Clamp arms not included but sold separately below. Body styles available are threaded with upper flange or non-threaded with lower or upper flange. | *$398.00 |
| Enerpac Hydraulic Power Workholding Swing Cylinder Long Arm No. CAL-122, Use w/cap.=2,600 lbs. (1 Each)
Brand: Enerpac Part Number: CAL-122
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$83.00 |
 | Enerpac Hydraulic Power Workholding Threaded Cylinder, Single Acting, No. WRT-21 (1 Each)
Brand: Enerpac Part Number: WRT-21
Cylinders can be fixtured into manual strap or bridge clamp assemblies. Fully threaded bodies allow cylinders to be threaded directly into tapped holes of the fixture for easy installation. Available as single-acting spring return or double acting hydraulic return. The VE-90 can use carbide grippers. | *$180.00 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-971ST (1 Each)
Brand: Enerpac Part Number: TS-971ST
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$83.00 |
| Enerpac Hydraulic Power Workholding Swing Cylinder Long Arm No. CAL-22, Use w/cap.=500 lbs. (1 Each)
Brand: Enerpac Part Number: CAL-22
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$52.00 |
 | Enerpac Hydraulic Power Workholding Turbo Air/Hydraulic Pump No. PACG-5002SB (1 Each)
Brand: Enerpac Part Number: PACG5002SB
A turbo air pump is recommended where input air pressure is limited. Engineered to recycle exhaust air to help power the pump. Maintains a tight pressure range for reliable clamping performance. Pump will automatically restart in the event of a pressure drop in the hydraulic system. Mounting plate allows for horizontal or vertical machine-side mounting. Buna-N polyurethane and Teflon seals. | *$646.00 |
 | Enerpac Hydraulic Power Workholding Jam Nut No. JN-12, 1 7/8-16 (1 Each)
Brand: Enerpac Part Number: FN-481 | *$34.00 |
 | Enerpac Hydraulic Power Workholding Hollow Cylinder, No. CY2129-5 (1 Each)
Brand: Enerpac Part Number: CY2129-5
These hollow cylinders combine compactness with power and versatility. Any application requiring either a pushing or pulling action is easily handled with this type of cylinder. The cylinders are threaded and can be placed over a bolt or a stud to upgrade most existing manual clamping fixtures. | *$366.00 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-9191ST (1 Each)
Brand: Enerpac Part Number: TS-9191ST
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$92.00 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-2131ST (1 Each)
Brand: Enerpac Part Number: CST-2131
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$95.00 |
 | Enerpac Hydraulic Power Workholding Sequence Valve For Time Interval Control No. V-2000 (1 Each)
Brand: Enerpac Part Number: V-2000
These valves can be plumbed to provide a sequence of clamping functions from just one hydraulic power source. Sequenced locating, clamping, and/or supporting functions can be controlled in a logical order by plumbing one sequence valve to each clamping group requiring a different time interval. The valve can be preset to different pressure values, allowing fluid flow in sequence as the hydraulic pressure increases in the entire system to whatever the power source provides, after all valves are open. These valves are basically timers, not pressure controllers. The VE-211 features a lock nut which secures the hydraulic pressure setting for the secondary circuit and a tamper proof cover can be placed over the set screw. Maximum operating pressure is 5,000 psi. | *$319.00 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder w/Arm No. SC-1, M=1 7/8-16 (1 Each)
Brand: Enerpac Part Number: SC-1
These swing cylinders rotate 90 degrees as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing, or pull applications by loosening the side plug and then rotating the plunger to a desired position. The VE-354 and VE-352 have a retract spring for single-acting operations. The VE-360 is only for double-acting operation and has no return spring. Clamp arm provided. Can be mounted with the built-in flange by securing the swinger to the top or bottom of a tooling plate or by screwing the threaded body into a mounting bracket. | *$687.00 |
| Enerpac Hydraulic Power Workholding Jam Nut No. JN-48, 1 5/16-16 (1 Each)
Brand: Enerpac Part Number: FN-331 | *$30.50 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-9131ST (1 Each)
Brand: Enerpac Part Number: CST9131
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$110.00 |
| Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-18251ST (1 Each)
Brand: Enerpac Part Number: CST18251
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$140.00 |
 | Enerpac RC-256 25 Ton Single Acting Hydraulic Cylinder
Brand: Enerpac Model: RC-256 Part Number: RC-256
Enerpac is the recognized global market leader in high pressure hydraulics. Manufacturer of hydraulic cylinders, pumps, valves, presses, tools, bolting tools, accessories and system components for the manufacturing and construction industries, for productions, maintenance, operation and repair.brbrCollapsed Height: 10.75"brCylinder Capacity: 25 TonsbrCylinder Effective Area: 5.15 Square InchesbrMaximum Operating Pressure: 10,000 psibrOil Capacity: 32.19 Cubic InchesbrStroke: 6.25"brWeight: 22 lbsbr | *$568.90 |
 | SEPTLS277WMC2000 - Self-Contained Hydraulic Cutters
Brand: Enerpac Part Number: 277-WMC-2000
Self-Contained Hydraulic Cutters | *$2,000.00 |
 | Enerpac Hydraulic Power Workholding Threaded Cylinder, Double Acting, No. WMT-39 (1 Each)
Brand: Enerpac Part Number: WMT-39
Cylinders can be fixtured into manual strap or bridge clamp assemblies. Fully threaded bodies allow cylinders to be threaded directly into tapped holes of the fixture for easy installation. Available as single-acting spring return or double acting hydraulic return. The VE-90 can use carbide grippers. | *$273.00 |
| Enerpac Hydraulic Power Workholding Turbo Air/Hydraulic Pump No. PACG-3002SB (1 Each)
Brand: Enerpac Part Number: PACG-3002SB
A turbo air pump is recommended where input air pressure is limited. Engineered to recycle exhaust air to help power the pump. Maintains a tight pressure range for reliable clamping performance. Pump will automatically restart in the event of a pressure drop in the hydraulic system. Mounting plate allows for horizontal or vertical machine-side mounting. Buna-N polyurethane and Teflon seals. | *$712.00 |
